View D2JW-01K31-MD_1231091.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Watertight Subminiature Basic Switch
Ultra-small and Highly Sealed
Water-tight housing (reference to IP67). Wide range of operating temperature from -40C to 85C. Gold crossbar contact and coil spring offer long life expectancy and high contact reliability.
D2JW
Ordering Information
Actuator Solder Model Molded lead wire
Pin plunger Hinge lever Hinge lever Simulated hinge lever
D2JW-011 D2JW-01K1A1 D2JW-01K11 D2JW-01K31
D2JW-011-MD D2JW-01K1A1-MD D2JW-01K11-MD D2JW-01K31-MD
Hinge roller lever
D2JW-01K21
D2JW-01K21-MD
Note:
The standard lengths of the lead wires (AV0.3f) of models incorporating them are 30 cm.
133
D2JW
D2JW
Specifications
Ratings/Characteristics
Operating speed Operating frequency Insulation resistance Contact resistance Dielectric strength 1 mm to 250 mm/s (at pin plunger) Mechanical: 240 operations/min Electrical: 60 operations/min 100 M min. (at 500 VDC) 100 m max. (molded lead models: 140 m min.) 600 VAC, 50/60 Hz for 1 min between contacts of the same polarity 1,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal part 0.1 A at 30 VDC (resistive load) Malfunction: 10 to 55 Hz, 1.5-mm double amplitude Malfunction: 200 m/s2 (approx. 20G) Destruction: 1,000 m/s2 (approx. 100G) Mechanical: 1,000,000 operations min. Electrical: 100,000 operations min. Operating: -40C to 85C (with no icing) Operating: 35% to 98% max. IEC IP67 Approx. 7 g (molded leaf models, pin plunger model)
Electrical ratings Vibration resistance Shock resistance Life expectancy Ambient temperature Ambient humidity Enclosure rating Weight
Operating Characteristics
Model Pin plunger D2JW-011 OF max. RF min. PT max. OT min. MD max. OP 2.45 N (250 gf) 0.98 N (100 gf) 0.6 mm 0.3 mm 0.1 mm 8.10.3 mm Short hinge lever D2JW-01K1A1 1.15 N (117 gf) 0.22 N (23 gf) 5.4 mm 0.7 mm 0.5 mm 8.40.8 mm Hinge lever D2JW-01K11 0.80 N (82 gf) 0.15 N (16 gf) 6.4 mm 1.4 mm 0.7 mm 8.40.8 mm Simulated hinge lever D2JW-01K31 0.95 N (97 gf) 0.18 N (19 gf) 5.5 mm 1.1 mm 0.6 mm 10.30.8 mm Hinge roller lever D2JW-01K21 0.98 N (100 gf) 0.19 N (20 gf) 5.2 mm 1.1 mm 0.5 mm 14.60.8 mm
Contact Form
COM NO NC (Black*) (Blue*) (Red*)
*Indicates the color of the lead wire.
134
D2JW
D2JW
Nomenclature
Rubber seal (silicone rubber) Cover (polycarbonate resin)
Soldered Epoxy resin
COM Black
NO Blue Red
NC
Dimensions
Note: 1. All units are in millimeters unless otherwise indicated. 2. Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
Pin Plunger
D2JW-011
PT
1.6 dia.
OP
2.35 -0.025 dia. 2.5 -0.025 dia.
+0.05
+0.05
Short Hinge Lever
D2JW-01K1A1
PT
0.3 t stainless steel spring lever
OP
2.5 -0.025 dia.
+0.05
2.35 -0.025 dia.
+0.05
Hinge Lever
D2JW-01K11
PT
0.3 t stainless steel spring lever
OP
2.5 -0.025 dia.
+0.05
2.35 -0.025 dia.
+0.05
12.7
135
D2JW
Simulated Hinge Lever
D2JW-01K31
OP PT
D2JW
0.3 t stainless steel spring lever
2.35 -0.025 dia. 2.5 -0.025 dia.
+0.05
+0.05
Hinge Roller Lever
D2JW-01K21
PT 4.8 x 2.2 dia. resin roller
OP
Molded Lead Wire
D2JW-01jjj-MD Note: Alphabets and numbers are inserted in j by the actuator.
PT
2.5 -0.025 dia.
+0.05
2.35 -0.025 dia.
+0.05
1.6 dia. 2.35 +0.05 dia. -0.025
OP
2.5 -0.025 dia.
+0.05
NC (red) NO (blue) COM (black)
Precautions
Mounting
Use M2.3 mounting screws with plain or spring washers to mount the switch. Tighten the screws to a torque of 0.20 to 0.29 N S m (2 to 3 kg S cm). Mounting Holes
M2.3 mounting holes
Because the switch uses polycarbonate resin as material for its component parts, contact OMRON if the switch material is likely to deteriorate due to adherence of oil or chemicals to the switch housing.
Soldering
To solder the lead to the terminal, apply a soldering iron rated at 30 W max. (temperature of soldering iron: 280C max.) within 3 seconds. Applying a soldering iron for too long a time or using one that is rated at more than 30 W may degrade the switch characteristics.
4.8 0.1
136
D2JW
Operation
Make sure that the operating body pushes the switch actuator with an adequate force when the switch is to be operated, and that it does not touch the actuator when the switch is released. Install the pin plunger switch so that the operating force is applied in alignment with the stroke of actuator. Do not apply a shock to the actuator; otherwise, the switch may be damaged. Do not apply excessive force to the actuator of the lever switch in the operating, releasing and horizontal directions.
D2JW
Leave the test piece in water for 30 min with the top of the test piece submerged 15 cm or more below the water level and the bottom of the test piece submerged 1 m or more below the water level. This test is to check the ingress of water into the switch enclosure after submerging the switch in water for a given time. Even if this test condition is met, the switch cannot be used in water.
Enclosure Ratings
The D2JW satisfies the following test condition specified by the IEC Publication 529: Enclosure rating: IP67 See the figure below. Test method:
EEEEE EEEEE EEEEE
Note:
Water 15 cm min 1m min Leave for 30 minutes Test piece
Temperature difference between the test piece and water must be 5C or more.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. B40-E1-1A
137

▲Up To Search▲

Price & Availability of D2JW-01K31-MD

	To Download D2JW-01K31-MD Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .